Your house can look like this 

Amazing Before and After

In Just a Few Days !

Installation Pictures

Easy to Apply

	DO IT YOURSELF EASILY
	KEEP YOUR ATTIC COOLER

APPLICATION INSTRUCTIONS

PREPARATION (CLEANING): Remover dirt, grease, wax, oil, mildew, loose paint and excessive chalk form surface with a high pressure washing followed by a bleach rinse to remove any mildew. Repair any cracks with THERMAL COOL CRACK PATCH before applying AC64. All surfaces must be clean and dry. When dealing with new stucco or masonry wait a least 14 days before applying and only apply to clean dry surface.

STEP 1

THERMAL COOL ACRYLIC SEALER is a highly concentrated, water borne, acrylic, super binding emulsion used as a chalk sealer for locking down chalky surfaces and a binder for adhesion of top-coat and pure acrylic. Our sealer also makes an excellent waterproofing sealer and conditioner for stucco, masonry, cement, wood, brick, granite, and almost any surface. Also as a primer is water, mildew and alkaline resistant. Stands tough against salt and mild acid's. This sealer applies milky white and dries clear, it penetrates deep into pours, locks down chalk, and primes in one easy application.

APPLICATION Apply this sealer with a low pressure garden type hand sprayer, roller and brush may be used. Apply evenly with overlapping strokes to insure complete coverage in one coat, avoiding pooling of product. A second coat may be applied after one hour. This sealer dries in 2 -4 hours, a complete cure within 24 hours. Apply when temperature is between 50 - 90 degrees.

PHYSICAL PROPERTIES Appearance milky white, solids 60-61%,pH 9.0 to 9.5 Viscosity Approx. 600cps., weight per gallon 8.8 to 8.9 lbs., specific gravity 1.06, dry bulking value. 107 gal/lb.

STEP 2

THERMAL COOL FIBERED INSULATED COATING is a waterproof fibrous pure acrylic compound for roofs, exterior walls, interior walls, stucco, roof tile, banding, brick, all other masonry surfaces, and a s a tile fill compound. Fib is also recommended for repairing and maintaining the water proofing system and sealing seams in corrugated and standing seam metal roofs. Fib contains a THERMAL COOLS secret fibrous additive which increases tensile strength and maximum stress levels. Fib will expand and contract with the substrate to help prevent hairline cracking and water intrusion. Provides a durable, flexible, waterproof elastic membrane specifically formulated to prevent cracking under the most extreme conditions.

APPLICATION: This product is a butter grade and may be applied by brush or squeegee. To apply by brush, scoop FIB caulk with a semi stiff brush and apply to roof/wall. Once FIB is applied to surface, use the brush to spread the product over any cracks. (ROOF) Using a squeegee pour out of bucket on roof and apply in a upward motion. Roughly covers approximately 200-250 sq. ft. per 5 gallon container.

SPECIFICATIONS: Mechanical Properties: Test temperature 76 degrees F, Tensile strength (max stress) lbs/in2 117, Tensile strength (break) lbs/in2 113, % Elongation (max stress) 910, % Elongation (fail) 1035, % Recovery after 25% Elongation 83.

STEP 3

INSULATING WATERPROOFING COATING is a waterproofing coating for sloped roofs and exterior walls. Use on cement tile, Bermuda tile, barrel tile, shingle, brick, block, stucco and all masonry surfaces. Mastic Thermal cool has the highest level of mildewcides available to protect your building or residence from fungal growth for years to come. Mastic will expand and contract with the substrate to help prevent hairline cracking and water intrusion. Provides a durable, flexible, waterproof elastic coating specifically formulated to adapt to any type climate.

APPLICATION: Use Thermal cools mastic straight from container. Use brush, roller or airless sprayer. Apply generously using overlapping strokes. Mastic dries tack free in 1 to 2 hours. Can be recoated in 2 to 4 hours. DO NOT APPLY when temperature is below 50 degrees.

COVERAGE: ROOF A two coat application of 80 Sq. Ft. per gallon will yield approximately a recommended 20 dry mils of thickness.

WALLS A one coat application of 150 sq. ft. per gallon will yield a recommended 7 dry mils of thickness.

SPECIAL NOTE: Mastic is a primary coating which must be followed by a finish coat application of Thermal cool Ceramic roof gloss.